CIY LED Limited

Meanwell Dali Dimmable LED Driver

Home > Products > Accessory > Non-waterproof LED Driver > Meanwell Dali Dimmable LED Driver

LCM-40DA

Output current level selectable by DIP S.W.
180~295VAC input only
Built-in active PFC function
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Built-in DALI interface and push dimming function
IP20 design
3 years warranty

Meanwell Dali Dimmable LED Driver

Output current level selectable by DIP S.W.
180~295VAC input only
Built-in active PFC function
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
Fully isolated plastic case
Class 2 power unit, no FG
Built-in DALI interface and push dimming function
Built-in 12V/50mA auxiliary
IP20 design
Temperature compensation function by external NTC
No load power consumption <1.2W(Note.7)
Power supplies synchronization function up to 10 units
Suitable for indoor LED lighting applications
3 years warranty

LCM -**DA Series

Wattage :

25W~60W

Features　:

180~295VAC input for 40W/60W, 180~277VAC input for 25W

Constant current mode

Built-in active PFC function

Multiple-stage output current level selectable by DIP switch

Built-in 3 in 1 dimming function for non DA type (0~10VDC, PWM signal or resistance, dim-to-off)

Built-in DALI interface and push dimming function for DA type

Suitable for indoor LED lighting applications

Model

DALI Dimming：LCM-25DA / LCM-40DA / LCM-60DA

MODEL		LCM-40DA
OUTPUT	SELECTABLE CURRENT Note.3	350mA	500mA	600mA	700mA	900mA	1050mA
	DC VOLTAGE	2 ~ 100V	2 ~ 80V	2 ~ 67V	2 ~ 57V	2 ~ 45V	2 ~ 40V
	RATED POWER	42W
	RIPPLE CURRENT	plus/minus 5%
	RIPPLE & NOISE (max.) Note.2	700mVp-p
	NO LOAD OUTPUT VOLTAGE (max.)	110V			65V
	CURRENT ACCURACY	plus/minus 5%
	SETUP, RISE TIME Note.5	1000ms, 80ms / 230VAC at rated power
	HOLD UP TIME (Typ.)	16ms/230VAC at rated power
INPUT	VOLTAGE RANGE Note.4	180 ~ 295VAC 254 ~ 417VDC
	FREQUENCY RANGE	47~63Hz
	POWER FACTOR	PF≥0.975/230VAC, PF≥0.96/277VAC at rated power (Please refer to "Power Factor Characteristic" section)
	TOTAL HARMONIC DISTORTION	Total harmonic distortion will be lower than 20% when output loading is 75% or higher
	EFFICIENCY (Typ.)	91%
	AC CURRENT	0.23A/230VAC 0.2A/277VAC
	INRUSH CURRENT (Typ.)	COLD START 20A (twidth=260us measured at 50% Ipeak) at 230VAC
	LEAKAGE CURRENT	<0.5mA / 240VAC
PROTECTION	SHORT CIRCUIT	Constant current limiting, recovers automatically after fault condition is removed
	OVER VOLTAGE	110 ~ 130V
		Protection type : Shutdown o/p voltage, re-power on to recover
	OVER TEMPERATURE	90celsius degrees plus/minus 10 celsius degree(RTH2)
		Protection type : Shut down o/p voltage, re-power on to recover
FUNCTION	AUXILIARY POWER	12V @ 50mA for driving fan; Tolerance plus/minus 5%
	TEMP. COMPENSATION	By external NTC(not provide with the power supply), please see "Temperature compensation operation"
	DIMMING	Please refer to "Dimming Operation" section
	SYNCHRONIZATION	Please refer to "Synchronization Operation" section
ENVIRONMENT	WORKING TEMP.	-30 ~ +60celsius degree (Refer to "Derating Curve")
	WORKING HUMIDITY	20 ~ 95% RH non-condensing
	STORAGE TEMP., HUMIDITY	-40 ~ +80,10~95% RH
	TEMP. COEFFICIENT	plus/minus 0.03%/ celsius degree (0 ~ 50celsius degree)
	VIBRATION	10 ~ 500Hz, 5G 12min./1cycle, period for 60min.each along X, Y,Z axes
SAFETY & EMC	SAFETY STANDARDS	UL8750, ENEC EN61347-1, EN61347-2-13,EN62384 independent approved
	DALI STANDARDS	Comply with IEC62386-101, 102, 207
	WITHSTAND VOLTAGE	I/P-O/P:3.75KVAC
	ISOLATION RESISTANCE	I/P-O/P:>100M Ohms / 500VDC / 25 celsius degree / 70% RH
	EMC EMISSION	Compliance to EN55015, EN61000-3-2 Class C(≥40% rated power) ; EN61000-3-3
	EMC IMMUNITY	Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547 light industry level (surge 2KV), criteria A
OTHERS	MTBF	193.6K hrs min. MIL-HDBK-217F (25celsius degree)
	DIMENSION	123.581.523mm (LWH)
	PACKING	0.24Kg ; 54pcs/15Kg/1.12CUFT
NOTE	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 celsius degree of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Please refer to "DIP Switch Table" section. 4. Derating may be needed under low input voltages. Please check the static characteristics for more details. 5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 6. Efficiency is measured at 500mA/80V output set by DIP switch. 7. No load power consumption<1.2W is measured at 180 277VAC, with lighting fixture connected and output current dimmed to 0%. 8. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

Note: the blank with * must be filled in.

*Name:
Country:
Company:
Website:
*E-mail:
Phone:
Subject:
Content:

- CIY LED LIMITED
Add:

Building A1,Huafengzhenbao lndustrial Park,Beihuan Road, Shiyan Town, Bao'an District,Shenzhen,China

Zip code:518108
Tel: +86 755 33101037
Email:info@ciy-led.com

- . Flora
- . Ivy
- . Walter

Meanwell Dali Dimmable LED Driver

LCM-40DA

Meanwell Dali Dimmable LED Driver

LCM -**DA Series

Wattage :

Features　:

Model

Note: the blank with * must be filled in.

About us

Products

Service

Contact us

Meanwell Dali Dimmable LED Driver

LCM-40DA

Meanwell Dali Dimmable LED Driver

LCM -**DA Series

Wattage :

Features :

Model

Note: the blank with * must be filled in.

About us

Products

Service

Contact us

Features　: